← Back to blog

Bathroom Vanities in Florida: Sizes, Styles and Costs

November 14, 2026
Bathroom Vanities in Florida: Sizes, Styles and Costs

The right vanity for a Florida bathroom is the widest one that still leaves safe clearances, built to handle humidity, and priced for the whole installed job, not just the cabinet. If you are in Orlando or Central Florida, you can see our vanity series in person, get free 3D bathroom design help and pick up or have your order delivered. This guide covers the decisions in the order you will face them.

Sunshine Home Material
sunshinehomematerial.com
Find a Vanity That Fits
Compare bathroom materials and get design guidance to help plan a vanity that suits your space, style, and budget.
Visit

TL;DR

  • Measure the whole installed fit (cabinet, top, door and drawer swing) before you pick a width. Common widths run from 24 to 72 inches.
  • Leave at least 30 inches of clear floor space in front of the vanity, per the NKBA bath planning guidelines.
  • In a humid Florida bathroom, moisture handling matters more than style: look at box material, finishes on every surface and a vented exhaust fan.
  • Floating vanities look open and clean but need solid wall support. Freestanding vanities are simpler to install.
  • Our Orlando vanity series list at $384 to $1,535, depending on the series and size, and you can see them at our showroom.

Table of Contents

Start with the room, not the catalog

Most vanity mistakes are measuring mistakes. A cabinet that is 48 inches wide on the product page may need more room once you add a countertop overhang, a faucet, a door that swings into the toilet or a drawer that hits the tub.

Measure these before you shop:

  1. Wall width where the vanity will go, from corner to corner or to the nearest obstruction.
  2. Depth the room can spare, including the countertop projection.
  3. Plumbing locations: where the drain and supply lines come out of the wall, and how far they sit from the side walls.
  4. Door and drawer movement: open the bathroom door fully and picture every cabinet door and drawer open at once.
  5. Ceiling and window height, if you want a tall mirror, a tower or wall lighting.

If you want a refresher on taking accurate measurements in a tight space, measuring the full fit carefully before you order is a habit that carries over from any trim or cabinet project. Measure twice, write the numbers down and bring them with you.

Vanity sizes and what fits where

Vanities are sold in standard widths, commonly 24, 30, 36, 48, 60 and 72 inches. A practical way to pick: choose the widest vanity that still leaves the clearances below.

Bathroom typeTypical vanityWhy it works
Powder room24 to 30 inch singleSmall footprint, leaves room to move
Hall or guest bath30 to 48 inch singleEnough drawer space for a shared bathroom
Primary bath60 or 72 inch, single or doubleRoom for two users and more storage

These are planning ranges, not rules. A 36-inch vanity in a narrow bathroom may be the better choice than a 48-inch one that crowds the door.

Clearances to respect

The National Kitchen & Bath Association's Bath Planning Guidelines recommend at least 30 inches of clear floor space from the front edge of a fixture to the opposite fixture, wall or obstacle. The same guidelines suggest a lavatory height between 32 and 43 inches to suit the people using it, and for accessible designs, a front edge no more than 34 inches above the floor.

In plain terms: stand where you will stand to brush your teeth. If your knees hit the tub or the door has to be half closed to open a drawer, go down a size.

Plumbing and building codes also set minimum spacing from a sink centerline to side walls and neighboring fixtures. Your installer or the local building department can confirm the numbers for your city and your project, and it is worth confirming them before you buy a vanity with a fixed sink position.

Single or double sink

A double vanity only makes sense when the room can handle it. You need the width for two basins with comfortable space between them and on each side, so 60 inches is generally the practical starting point. If you are weighing a double, sketch the basin and faucet positions at full scale on the wall with painter's tape. It is the fastest way to see whether two people can use it at the same time.

Painter’s tape marks a double vanity layout

On a rental or investment property, a well-sized single vanity with good drawer storage often serves tenants and buyers better than a cramped double.

Sunshine Home Material (Kitchen Remodeling Center), 1656 Goldenrod Road, 32807 Orlando
Sunshine Home Material
Explore Bathroom Materials in Person
See bathroom vanities and other renovation materials in person, and get design guidance for planning your bathroom project.
Sunshine Home Material (Kitchen Remodeling Center)
1656 Goldenrod Road, 32807 Orlando
Get directions

Floating vs. freestanding vanities

This is the choice that changes both the look and the installation.

Freestanding vanities sit on the floor. They have traditional, furniture-like proportions, the cabinet's weight rests on the floor and installation is simpler. They also hide uneven flooring edges and plumbing a bit more easily.

Floating (wall-mounted) vanities hang on the wall with open floor beneath. The floor is visible, which makes a small bathroom feel larger and makes mopping easier. The trade-off is structural: the wall has to carry the cabinet, the top, the sink and everything you store in it.

If you want a floating vanity, plan for it early:

  • Add solid blocking or plywood backing inside the wall before the drywall goes up, or open the wall during a remodel.
  • Use fasteners rated for the load, and match the anchor type to the wall. Many Central Florida homes have concrete block exterior walls, which call for masonry anchors rather than the screws you would use into wood studs.
  • Check where the drain and supply lines exit. A floating vanity usually needs the plumbing to line up with the cabinet's open back and drawer cutouts.
  • Pick a lighter top if the wall support is a concern.

We can help you sort the layout before you buy. Bring your wall measurements and plumbing locations to the showroom and we will go through the options with you, including the 3D design service.

Door and cabinet styles

The styles that come up most in Orlando homes:

  • Shaker: flat recessed-panel doors that suit both traditional and transitional bathrooms.
  • Flat-panel modern: slab doors and drawers, in matte or high-gloss finishes.
  • Furniture style: legs and trim that look like a piece of furniture rather than a built-in.
  • Double vanity with a tower: adds tall storage between or beside the sinks.
  • Open shelf: a shelf below or beside the cabinet for baskets and towels.

If you are matching a kitchen, check our frameless matte black and Luna grey Shaker finishes to carry the look through both rooms.

Materials that handle Florida humidity

A bathroom in Florida runs warm and damp for most of the year, and a vanity sits in the wettest spot in the room. The things that decide how long it lasts:

  • Box material. Solid hardwood is naturally moisture resistant, and House Digest notes that species such as teak, white oak and walnut can last upwards of 20 years with proper maintenance. The same article warns that MDF and particleboard can swell if water gets past the outer layer, and that plywood resists moisture better but can peel if exposed to too much humidity.
  • Finish on every surface. Water gets into the back, the inside and the bottom of a cabinet, not just the doors. A sealed cabinet bottom and a finish inside the box slow down moisture damage.
  • Hardware. Stainless, coated or solid brass hardware resists the corrosion that humid air and daily splashes cause on cheaper plated pieces.
  • Ventilation. An exhaust fan vented to the outside, and run during and after showers, does more for a vanity than any finish. A fan that vents into the attic leaves the moisture in your house.
  • Plumbing leaks. Check supply lines and the P-trap after installation and a few weeks later. A slow drip under a sink is the most common way a good vanity gets ruined.

Whatever the cabinet is made of, wipe standing water off the top and the base, and re-caulk the backsplash and the gap between top and wall when it starts to crack.

For the countertop, a quartz or stone top is a common pairing with a vanity. We also sell stone countertops and offer full fabrication services, so you can match the top to the cabinet in one order.

What bathroom vanities cost

Vanity prices vary a lot because several things stack up: width, sink count, box construction, stock versus semi-custom versus custom, the top material and extras such as soft-close drawers.

What bathroom vanities cost

For a national reference, HomeAdvisor reports that prefabricated vanities cost between $100 and $2,600, depending on size, materials and features. Installation runs from $300 to $2,200, with most homeowners spending around $1,500. A custom vanity costs between $500 and $2,800 for construction, plus $200 to $1,000 for installation. Those are national averages, so Florida labor rates and your bathroom's plumbing will move the number.

Our own vanity series are priced as published on our site:

SeriesPrice range
01-CX Vanities$384 to $522
02-IMO Vanities$456 to $780
03-IMO Vanities$387 to $690
03-WH Vanities$495 to $1,089
06-DOK Vanities$545 to $1,535

The range inside each series depends on the size and configuration you choose. You can browse all of them on our vanities by size and series page.

Plan the whole budget

The cabinet is only one line. A realistic budget for a vanity swap includes:

  1. The vanity and its top, if sold separately.
  2. The faucet, drain and supply lines.
  3. The sink, if it is not included.
  4. Hardware such as handles.
  5. Installation labor.
  6. Delivery or pickup.
  7. A cushion for surprises, such as rotted subfloor or outdated shutoff valves, that show up once the old vanity comes out.

When you buy materials from us, you get a project estimate and material quotation, so the numbers are on paper before you commit. Financing options are available for qualified buyers.

From order to installed vanity

Here is a straightforward order of work for a replacement:

  1. Measure the space and photograph the plumbing.
  2. Pick the size and style using the clearances above.
  3. Choose the top and sink, and check how the faucet holes line up.
  4. Order, and confirm delivery or pickup. We deliver in-stock materials in 24 to 48 hours, which helps when a contractor is waiting on the job.
  5. Shut off the water and remove the old vanity. Check the wall and floor behind it.
  6. Set the new vanity, level it, secure it to the wall and attach the top.
  7. Connect plumbing, run the water and look for leaks.
  8. Seal the edges with caulk and install hardware.

We offer assembly and delivery services, and professional installation services are available too. We also refer customers to independent installation professionals. Homeowners, contractors and property managers can all go through the same process, and contractors and wholesale buyers have access to purchasing support.

See the vanities in Orlando

If you are searching for bathroom vanities in Orlando, the quickest way to compare sizes and finishes is in person. We are a family-owned kitchen and bath materials supplier, showroom and design center, established in 2018, with two Orlando locations. You can look at the finishes, take samples and talk through your layout, and our design team can build a free 3D plan of your bathroom.

Sunshine Home Material

Start with our vanities by size and series, or contact us to set up a design consultation. If your project includes a kitchen too, our kitchen and bath remodeling page shows how we plan both rooms together.

Our perspective

Most of the budget problems we see on bathroom projects start before the order: the vanity does not fit the plumbing, the door hits the cabinet, or the top and the cabinet come from different places and do not line up.

That is why we put a design consultation and a 3D plan up front. Seeing the vanity, the top and the floor in the same drawing, then getting a material quote, lets you spend on the pieces that matter and skip the ones that do not.

We sell factory-direct and wholesale-oriented pricing to homeowners and to contractors, builders, designers and investors alike. A homeowner doing one bathroom and a contractor outfitting ten rental units want the same thing: the right size, a clear price and the material on site when the crew needs it.

If you are in Greater Orlando or Central Florida, start with the showroom. Bring your measurements and we will take it from there.

Sunshine Home Material

FAQ

What size bathroom vanity should I buy?

Choose the widest vanity that keeps at least 30 inches of clear floor space in front and room for the door and drawers to open. Powder rooms usually take 24 to 30 inches, hall baths 30 to 48 inches and primary baths 60 or 72 inches. Bring your measurements to our showroom and we can check the fit.

Is a floating vanity a good choice in Florida?

Yes, as long as the wall is prepared to carry it. Add solid backing before closing the wall, and use anchors that match the wall type, which in many Central Florida homes means masonry anchors for block walls. The open floor also makes cleaning easier in a humid climate.

How much does a bathroom vanity cost in Orlando?

Our vanity series are published at $384 to $1,535, depending on the series and size. National data from HomeAdvisor puts installation at $300 to $2,200, so budget for labor, plumbing parts and the top in addition to the cabinet.

Can contractors and investors buy vanities in volume?

Yes. We support contractors, builders, property managers and wholesale buyers with purchasing help, project estimates and material quotations. Contact us with your unit count and sizes and we will put together a quote.

Sources